SPARTUS®
EasyTIG
208P AC/DC
Lightweight TIG AC/DC PULS
Technical parameters
| Input | ~1× 230V ± 10% 50 / 60 Hz |
| Welding Current TIG [A] | AC 10 – 200 DC 10 – 170 |
| Duty cycle TIG [%] | AC 35 [200A] DC 40 [170A] |
| TIG PARAMETERS | |
| Start Amps, End Amps |  |
| Gas pre flow [s] | 0 – 2 |
| Up slope [s] | 0 – 10 |
| Down slope [s] | 0 – 10 |
| Gas post flow [s] | 0 – 10 |
| TIG PULSE mode | |
| Pulse Amps [A] | [AC] 10 – 200 [DC] 10 – 170 |
| Base Amps [A] | [AC] 10 – 200 [DC] 10 – 170 |
| Pulse Width [%] | 5 – 95 |
| Pulse frequency [Hz] | 0,5 – 200 |
| AC frequency [Hz] | 60 |
| AC Wave Forms | Square |
| AC balance [%] | 10 – 99 |
| 2T/4T Control | |
| Arc ignition | LIFT / HF |
| MMA PARAMETERS | |
| MMA welding mode [AC/DC] | |
| Welding current MMA [A] | AC 10 – 170 DC 10 – 170 |
| Duty cycle MMA [%] | AC 40 [170A] DC 40 [170A] |
| Hot Start range [%] | 0 – 10 |
| Arc Force range [%] | 0 – 10 |
| No-load voltage [V] | 79 |
| OTHER | |
| Current consumpiton [A] | 28 TIG DC / 33 TIG AC 41 MMA DC / 39 MMA AC |
| Power factor (cosφ) | 0,6 |
| Efficiency η [%] | 85 |
| Insulation class | H |
| Protection class | IP21S |
| Weight [kg] | 8,7 |
| Dimensions [mm] | 450 × 135 × 230 |
Description:
SPARTUS® Easy TIG 208P AC/DC is a modern digitally controlled inverter welding machine,
constructed on the basis of IGBTs. Allows welding TIG AC/DC and MMA AC/DC modes. It is powered with single-phase
230V source power.
Easy-to-use digital control panel provides instant access to the welding machine’s functions.
EasyTIG 208P AC/DC enables two methods of arc ignition:TIG HF (highfrequency) and TIG Lift (with scratch
ignition). A diagram of TIG parameters on the panel allows for full adjustment:
- gas flow time before and after welding
- up slope and down slope time.
In addition,the built-in pulse welding function (frequency 0.5 – 200Hz) enables adjustment: base amps,
pulse amps, pulse frequency. Thanks to these parameters the machine is perfect for joining even very thin
sheets.
Depending on the welder’s preferencesEasyTIG 208P AC/DC can work in 2T or 4T mode.
EasyTIG 208P AC/DC will work useful during welding aluminum, thanks to the smooth balance adjustment in the
range 10 - 99%.
MMA welding mode(to 200A) is assisted by functions: Arc Force and Hot Start.
EasyTIG 208P AC/DC is a perfect machinefor production and maintenance.
Examples of use: portable repair, workshop, maintenance, constructions.
EasyTIG 208P AC/DC package 17 4m:
Device SPARTUS® EasyTIG 208P AC/DC
TIG torch SPE 17 1B 4m
Set of consumables
work clamp
Gas hose
User's manual
Package price
[EUR]:
